Mechanical Performance and Sustainability Potential of Concrete Incorporating Waste Polytetrafluoroethylene Fibers
DOI:
https://doi.org/10.58524/ijhes.v5i2.1242Abstract
This study investigates the feasibility of utilizing waste polytetrafluoroethylene (PTFE) fibers as a recycled additive in concrete to support plastic waste valorization and sustainable construction material development. Waste PTFE fibers obtained from industrial seal production were mechanically processed into irregular fiber-like particles with sizes of approximately 4–6 mm and incorporated into concrete mixtures at 0.2%, 0.4%, 0.6%, and 0.8% by weight of concrete. The effects of PTFE fiber addition on workability, splitting tensile strength, and flexural strength were evaluated using cylindrical and beam specimens tested according to SNI and ASTM standards. The results show that increasing PTFE fiber content reduced concrete workability, as indicated by a decrease in slump from 125 mm for the control mixture to 75 mm for the mixture containing 0.8% PTFE fibers. The incorporation of untreated PTFE fibers also decreased mechanical strength. Compared with the control concrete, splitting tensile strength decreased by 6.924%–18.474%, while flexural strength decreased by 15.409%–32.060%. This reduction is attributed to the smooth, hydrophobic, chemically inert, and low-friction surface characteristics of PTFE, which weaken adhesion between the fibers and the cementitious matrix and reduce load-transfer efficiency. Although untreated waste PTFE fibers did not improve the tensile-related mechanical performance of concrete, their use may contribute to plastic waste utilization in construction materials. Further surface treatment, fiber modification, and mix design optimization are required before waste PTFE fibers can be effectively applied as reinforcing materials in sustainable concrete.
References
Abdulateef, L. A., Hassan, S. H., & Ahmed, A. M. (2024). Exploring the mechanical behavior of concrete enhanced with fibers derived from recycled plastic bottles. Engineering, Technology & Applied Science Research, 14(2), 13481–13486. https://doi.org/10.48084/etasr.6895
Adajar, M. A., & Ubay-Anongphouth, I. O. (2022). Effects of polyethylene terephthalate (PET) plastics on the mechanical properties of fly ash concrete. International Journal of GEOMATE, 23(95), 162–167. https://doi.org/10.21660/2022.95.1576
Almohana, A. I., Abdulwahid, M. Y., Galobardes, I., Mushtaq, J., & Almojil, S. F. (2022). Producing sustainable concrete with plastic waste: A review. Environmental Challenges, 9, 100626. https://doi.org/10.1016/j.envc.2022.100626
ASTM International. (2002). ASTM C78-02: Standard test method for flexural strength of concrete using simple beam with third-point loading. ASTM International.
ASTM International. (2008). ASTM C496/C496M-04e1: Standard test method for splitting tensile strength of cylindrical concrete specimens. ASTM International.
Çelik, A. I., Özkılıç, Y. O., Zeybek, Ö., Özdöner, N., & Tayeh, B. A. (2022). Performance assessment of fiber-reinforced concrete produced with waste lathe fibers. Sustainability, 14(19), 11817. https://doi.org/10.3390/su141911817
Dhanumalayan, E., & Joshi, G. M. (2018). Performance properties and applications of polytetrafluoroethylene (PTFE)—A review. Advanced Composites and Hybrid Materials, 1(2), 247–268. https://doi.org/10.1007/s42114-018-0023-8
Faraj, R. H., Ali, H. F. H., Sherwani, A. F. H., Hassan, B. R., & Karim, H. (2020). Use of recycled plastic in self-compacting concrete: A comprehensive review on fresh and mechanical properties. Journal of Building Engineering, 30, 101283. https://doi.org/10.1016/j.jobe.2020.101283
Figueiredo, F., da Silva, P., Botero, E. R., & Maia, L. (2022). Concrete with partial replacement of natural aggregate by PET aggregate: An exploratory study about the influence on compressive strength. AIMS Materials Science, 9(2), 172–183.
Foti, D. (2011). Preliminary analysis of concrete reinforced with waste bottle PET fibers. Construction and Building Materials, 25, 1906–1915. https://doi.org/10.1016/j.conbuildmat.2010.11.066
Fraternali, F., Ciancia, V., Chechile, R., Rizzano, G., Feo, L., & Incarnato, L. (2011). Experimental study of thermo-mechanical properties of recycled PET fiber-reinforced concrete. Composite Structures, 93, 2368–2374. https://doi.org/10.1016/j.compstruct.2011.03.025
Kim, S. B., Yi, N. H., Kim, H. Y., Kim, J. J., & Song, Y. C. (2010). Material and structural performance evaluation of recycled PET fiber reinforced concrete. Cement and Concrete Composites, 32, 232–240. https://doi.org/10.1016/j.cemconcomp.2009.11.002
Manso-Morato, J., Hurtado-Alonso, N., Revilla-Cuesta, V., & Skaf, M. (2024). Fiber-reinforced concrete and its life cycle assessment: A systematic review. Journal of Building Engineering, 94, 110062. https://doi.org/10.1016/j.jobe.2024.110062
Marinelli, S., Marinello, S., Lolli, F., Gamberini, R., & Coruzzolo, A. M. (2023). Waste plastic and rubber in concrete and cement mortar: A tertiary literature review. Sustainability, 15(9), 7232. https://doi.org/10.3390/su15097232
Mazur, K., Gądek-Moszczak, A., Liber-Kneć, A., & Kuciel, S. (2021). Mechanical behavior and morphological study of polytetrafluoroethylene (PTFE) composites under static and cyclic loading conditions. Materials, 14, 1712. https://doi.org/10.3390/ma14071712
Mercante, I., Aleandri, G. A., Bove, F., Savoia, M., & Ragone, M. (2020). Fresh and hardened properties of concrete containing different forms of plastic waste: A review. Waste Management, 113, 157–175. https://doi.org/10.1016/j.wasman.2020.05.048
Nyika, J., & Dinka, M. (2022). Recycling plastic waste materials for building and construction materials: A mini-review. Materials Today: Proceedings, 62, 3257–3262. https://doi.org/10.1016/j.matpr.2022.04.226
Ochi, T., Okubo, S., & Fukui, K. (2007). Development of recycled PET fiber and its applications as concrete-reinforcing fiber. Cement and Concrete Composites, 29, 448–455. https://doi.org/10.1016/j.cemconcomp.2007.02.002
Saikia, N., & de Brito, J. (2014). Mechanical properties and abrasion behavior of concrete containing shredded PET bottle waste as a partial substitution of natural aggregate. Construction and Building Materials, 52, 236–244. https://doi.org/10.1016/j.conbuildmat.2013.11.049
Standar Nasional Indonesia. (1997). Metode pengujian kuat lentur beton dengan balok uji sederhana (SNI 03-4431-1997). Badan Standardisasi Nasional.
Standar Nasional Indonesia. (2000). Tata cara pembuatan rencana campuran beton normal (SNI 03-2834-2000). Badan Standardisasi Nasional.
Su, J., Jiang, Z., Fang, C., Yang, M., Wu, L., & Huang, Z. (2022). The reinforcing effect of waste polyester fiber on recycled polyethylene. Polymers, 14(15), 3109. https://doi.org/10.3390/polym14153109
Wang, Y., Zhang, P., Liu, J., Zhao, T., Li, Q., & Chen, X. (2023). Upcycling of recycled plastic fiber for sustainable cementitious composites: A critical review and new perspective. Cement and Concrete Composites, 142, 105192. https://doi.org/10.1016/j.cemconcomp.2023.105192
Downloads
Published
Issue
Section
License
Copyright (c) 2026 Lilis Zulaicha, Oggi Heicqal Ardian, Anggi Hermawan
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
